View V-15-1A5_7440920.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

110 miniature basic switch v reliable basic switches in a wide variation wide variation of best-selling microswitches with switching currents of 10 to 21 a. can be used for interrupting current when doors are opened or closed. available in two types of cases: thermoplastic resin and thermosetting resin. ordering information model number legend v- - - 123 4567 8 1. ratings 21: 21 a at 250 vac 16: 16 a at 250 vac 15: 15 a at 250 vac 11: 11 a at 250 vac 10: 10 a at 250 vac 2. contact gap none: 1 mm (f gap) g: 0.5 mm (g gap) (for remodelling) 3. actuator none: pin plunger 1: short hinge lever 2: hinge lever 3: long hinge lever 4: simulated roller lever 5: short hinge roller lever 6: hinge roller lever 4. contact form 1: spdt (com bottom terminal, double-throw) 2: spst-nc (com bottom terminal, normally closed) 3: spst-no (com bottom terminal, normally open) 4: spdt (com side terminal, double-throw) 5: spst-nc (com side terminal, normally closed) 6: spst-no (com side terminal, normally open) 5. terminals a: solder terminals c2: quick-connect terminals (#187) c: quick-connect terminals (#250) b: screw terminals 6. barrier (models with thermoplastic case only) none: without barrier r: right-hand barrier l: left-hand barrier 7. maximum operating force 6: 3.92 n {400 gf} 5: 1.96 n {200 gf} 4: 0.98 n {100 gf} note: these values are for the pin plunger models. 8. special purpose (models with thermosetting case only) t: heat-resistive
v v 111 available combinations terminal thermoplastic case thermosetting case terminal model v-21 v-16 v-11 v-15 v-10 rated current 21 a 16 a 11 a 15 a 10 a com terminal position insulation barrier heat resistance of terminal symbol 3.92 n {400 gf} 3.92 n {400 gf} 1.96 n {200 gf} 0.98 n {100 gf} 3.92 n {400 gf} 1.96 n {200 gf} 1.96 n {200 gf} 0.98 n {100 gf} bottom no standard (80 c) solder terminals (a) --- bottom no standard (80 c) quick-connect terminals (#187) (c2) --- quick-connect terminals (#250) (c) screw terminals (b) --- --- --- (1.96 n) heat it t solder terminals (a) --- --- --- --- heat resistant (150 c) quick-connect terminals (#187) (c2) --- --- --- --- quick-connect terminals (#250) (c) --- --- --- --- --- --- --- --- screw terminals (b) --- --- --- --- --- --- --- --- yes standard (80 c) solder terminals (a) --- --- --- --- --- --- yes standard (80 c) quick-connect terminals (#187) (c2) --- --- --- --- --- --- quick-connect terminals (#250) (c) --- --- --- --- --- side no standard (80 c) solder terminals (a) --- --- --- --- side no standard (80 c) quick-connect terminals (#187) (c2) --- --- --- --- quick-connect terminals (#250) (c) --- --- --- --- --- --- --- note: 1. : standard : semi-standard 2. consult your omron sales representative for spacific models with standard approvals. list of models general-purpose models (only combinations with standard terminals are shown.) thermoplastic case actuator com til contact f terminals (t) 21 a (of: 3.92 n {400 gf}) terminal position form (see note) without barrier right-hand barrier left-hand barrier pin plunger bottom spdt c v-21-1c6 v-21-1cr6 v-21-1cl6 spst-nc v-21-2c6 v-21-2cr6 v-21-2cl6 spst-no v-21-3c6 v-21-3cr6 v-21-3cl6 short hinge lever spdt v-211-1c6 v-211-1cr6 v-211-1cl6 hinge lever v-212-1c6 v-212-1cr6 v-212-1cl6 long hinge lever v-213-1c6 v-213-1cr6 v-213-1cl6 simulated roller lever v-214-1c6 v-214-1cr6 v-214-1cl6 short hinge roller lever v-215-1c6 v-215-1cr6 v-215-1cl6 hinge roller lever v-216-1c6 v-216-1cr6 v-216-1cl6 note: c: quick-connect terminals (#250)
v v 112 actuator com til contact f terminals (t) 16 a (of: 1.96 n {200 gf}) terminal position form (see note) without barrier right-hand barrier left-hand barrier pin plunger bottom spdt a v-16-1a5 v-16-1ar5 v-16-1al5 c2 v-16-1c25 v-16-1c2r5 v-16-1c2l5 c v-16-1c5 --- --- spst-nc a v-16-2a5 v-16-2ar5 v-16-2al5 c2 v-16-2c25 v-16-2c2r5 v-16-2c2l5 c v-16-2c5 --- --- spst-no a v-16-3a5 v-16-3ar5 v-16-3al5 c2 v-16-3c25 v-16-3c2r5 v-16-3c2l5 c v-16-3c5 --- --- short hinge lever spdt a v-161-1a5 v-161-1ar5 v-161-1al5 g c2 v-161-1c25 v-161-1c2r5 v-161-1c2l5 c v-161-1c5 --- --- hinge lever a v-162-1a5 v-162-1ar5 v-162-1al5 g c2 v-162-1c25 v-162-1c2r5 v-162-1c2l5 c v-162-1c5 --- --- long hinge lever a v-163-1a5 v-163-1ar5 v-163-1al5 c2 v-163-1c25 v-163-1c2r5 v-163-1c2l5 c v-163-1c5 --- --- simulated roller lever a v-164-1a5 v-164-1ar5 v-164-1al5 c2 v-164-1c25 v-164-1c2r5 v-164-1c2l5 c v-164-1c5 --- --- short hinge roller lever a v-165-1a5 v-165-1ar5 v-165-1al5 g roller lever c2 v-165-1c25 v-165-1c2r5 v-165-1c2l5 c v-165-1c5 --- --- hinge roller lever a v-166-1a5 v-166-1ar5 v-166-1al5 c2 v-166-1c25 v-166-1c2r5 v-166-1c2l5 c v-166-1c5 --- --- note: a: solder terminals c2: quick-connect terminals (#187) c: quick-connect terminals (#250)
v v 113 actuator com terminal iti contact form terminals (see note) 11 a (of: 0.98 n {100 gf} position () without barrier pin plunger bottom spdt a v-11-1a4 c2 v-11-1c24 c v-11-1c4 short hinge lever a v-111-1a4 g c2 v-111-1c24 c v-111-1c4 hinge lever a v-112-1a4 g c2 v-112-1c24 c v-112-1c4 long hinge lever a v-113-1a4 c2 v-113-1c24 c v-113-1c4 simulated roller lever a v-114-1a4 c2 v-114-1c24 c v-114-1c4 short hinge roller lever a v-115-1a4 g c2 v-115-1c24 c v-115-1c4 hinge roller lever a v-116-1a4 g c2 v-116-1c24 c v-116-1c4 note: a: solder terminals c2: quick-connect terminals (#187) c: quick-connect terminals (#250)
v v 114 thermosetting case actuator com terminal contact form terminals (see note 15 a 10 a terminal position form (see note 1) of: 1.96 n {200 gf} of: 1.96 n {200 gf} of: 0.98 n {100 gf} pin plunger bottom spdt a V-15-1A5 v-10-1a5 v-10-1a4 c2 v-15-1c25 v-10-1c25 v-10-1c24 b v-15-1b5 v-10-1b5 v-10-1b4 spst-nc a v-15-2a5 v-10-2a5 v-10-2a4 c2 v-15-2c25 v-10-2c25 v-10-2c24 b v-15-2b5 v-10-2b5 v-10-2b4 spst-no a v-15-3a5 v-10-3a5 v-10-3a4 c2 v-15-3c25 v-10-3c25 v-10-3c24 b v-15-3b5 v-10-3b5 v-10-3b4 side spdt a v-15-4a5 v-10-4a5 v-10-4a4 spst-nc v-15-5a5 v-10-5a5 v-10-5a4 spst-no v-15-6a5 v-10-6a5 v-10-6a4 short hinge lever bottom spdt a v-151-1a5 v-101-1a5 v-101-1a4 g c2 v-151-1c25 v-101-1c25 v-101-1c24 b v-151-1b5 v-101-1b5 v-101-1b4 hinge lever a v-152-1a5 v-102-1a5 v-102-1a4 g c2 v-152-1c25 v-102-1c25 v-102-1c24 b v-152-1b5 v-102-1b5 v-102-1b4 long hinge lever a v-153-1a5 v-103-1a5 v-103-1a4 c2 v-153-1c25 v-103-1c25 v-103-1c24 b v-153-1b5 v-103-1b5 v-103-1b4 simulated roller lever a v-154-1a5 v-104-1a5 v-104-1a4 c2 v-154-1c25 v-104-1c25 v-104-1c24 b v-154-1b5 v-104-1b5 v-104-1b4 short hinge roller lever a v-155-1a5 v-105-1a5 v-105-1a4 roller lever c2 v-155-1c25 v-105-1c25 v-105-1c24 b v-155-1b5 v-105-1b5 v-105-1b4 hinge roller lever a v-156-1a5 v-106-1a5 v-106-1a4 c2 v-156-1c25 v-106-1c25 v-106-1c24 b v-156-1b5 v-106-1b5 v-106-1b4 note: 1. a: solder terminals c2: quick-connect terminals (#187) b: screw terminals 2. of values shown in the table are for the pin plunger models.
v v 115 heat resistant models (up to 150 c) actuator com terminal contact form terminals 15 a 10 a term i na l position of: 1.96 n {200 gf} of: 0.98 n {100 gf} pin plunger bottom spdt solder termi- l (a) V-15-1A5-t v-10-1a4-t short hinge lever nals (a) v-151-1a5-t v-101-1a4-t hinge lever v-152-1a5-t v-102-1a4-t long hinge lever v-153-1a5-t v-103-1a4-t simulated roller lever v-154-1a5-t v-104-1a4-t short hinge roller lever v-155-1a5-t v-105-1a4-t hinge roller lever v-156-1a5-t v-106-1a4-t barrier (v-21 and v-16 models only) right-hand barrier left-hand barrier specifications ratings item resistive load model rated voltage v-21 250 vac 21 a 125 vdc 250 vdc 0.6 a 0.3 a v-16 250 vac 16 a 125 vdc 250 vdc 0.6 a 0.3 a v-15 250 vac 15 a 125 vdc 250 vdc 0.6 a 0.3 a v-11 250 vac 11 a 125 vdc 250 vdc 0.6 a 0.3 a v-10 250 vac 10 a 125 vdc 250 vdc 0.6 a 0.3 a note: the ratings values apply under the following test conditions: ambient temperature: 20 2 c ambient humidity: 65 5% operating frequency: 30 operations/min
v v 116 switching capacity per load (reference values) model voltage non-inductive load inductive load resistive load lamp load inductive load motor load nc no nc no nc no nc no v-21 250 vac 21 a 3 a 12 a 4 a 8 vdc 21 a 5 a 12 a 7 a 30 vdc 14 a 5 a 12 a 5 a 125 vdc 0.6 a 0.1 a 0.6 a 0.1 a 250 vdc 0.3 a 0.05 a 0.3 a 0.05 a v-16 250 vac 16 a 2 a 10 a 3 a 8 vdc 16 a 4 a 10 a 6 a 30 vdc 10 a 4 a 10 a 4 a 125 vdc 0.6 a 0.1 a 0.6 a 0.1 a 250 vdc 0.3 a 0.05 a 0.3 a 0.05 a v-15 250 vac 15 a 2 a 10 a 3 a 8 vdc 15 a 4 a 10 a 6 a 30 vdc 10 a 4 a 10 a 4 a 125 vdc 0.6 a 0.1 a 0.6 a 0.1 a 250 vdc 0.3 a 0.05 a 0.3 a 0.05 a v-11 250 vac 11 a 1.5 a 6 a 2 a 8 vdc 11 a 3 a 6 a 3 a 30 vdc 6 a 3 a 6 a 3 a 125 vdc 0.6 a 0.1 a 0.6 a 0.1 a 250 vdc 0.3 a 0.05 a 0.3 a 0.05 a v-10 250 vac 10 a 1.5 a 6 a 2 a 8 vdc 10 a 3 a 6 a 3 a 30 vdc 6 a 3 a 6 a 3 a 125 vdc 0.6 a 0.1 a 0.6 a 0.1 a 250 vdc 0.3 a 0.05 a 0.3 a 0.05 a note: 1. the above current values are the normal current values of models with a contact gap of 1 mm (gap f), which vary with the norm al current values of models with a contact gap of 0.5 mm (gap g). 2. inductive load has a power factor of 0.4 min. (ac) and a time constant of 7 ms max. (dc). 3. lamp load has an inrush current of 10 times the steady-state current. 4. motor load has an inrush current of 6 times the steady-state current.
v v 117 characteristics operating speed 0.1 mm to 1 m/s (pin plunger models) operating frequency mechanical: 600 operations/min max. electrical: 30 operations/min max. insulation resistance 100 m ? min. (at 500 vdc) contact resistance (initial value) 15 m ? max. dielectric strength (t2) 1,000 vac, 50/60 hz for 1 min between terminals of the same polarity g (see note 2) v-21, v-16, and v-11 models: 2,000 vac, 50/60 hz for 1 min between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal parts v-15 and v-10 models: 1,500 vac, 50/60 hz for 1 min between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal parts vibration resistance (see note 3) malfunction: 10 to 55 hz, 1.5-mm double amplitude shock resistance (see note 3) destruction: 1,000 m/s 2 {approx. 100g} max. malfunction: v-21/v-16/v-15: 300 m/s 2 {approx. 30g} max. v-11/v-10: 200 m/s 2 {approx. 20g} max. durability (see note 4) mechanical: 50,000,000 operations min. (60 operations/min) electrical: v-21/v-16/v-15: 100,000 operations min. (30 operations/min) (v-15 heat resistive: 20,000 operation min. (30 operations/min)) v-11/v-10: 300,000 operations min. (30 operations/min) (v-10 heat resistive: 50,000 operation min. (30 operations/min)) degree of protection iec ip40 degree of protection against electric shock class i proof tracking index (pti) 175 ambient operating temperature ?25 c to 80 c (at ambient humidity of 60% max.) (with no icing) ?25 c to 150 c for heat-resistive model (at ambient humidity of 60% max.) (with no icing) ambient operating humidity 85% max. (for 5 c to 35 c) weight approx. 6.2 g (pin plunger models) note: 1. the data given above are initial values. 2. the dielectric strength values shown in the table are for models with a separator. 3. for the pin plunger models, the above values apply for use at both the free position and total travel position. for the lever models, they apply at the total travel position. 4. for testing conditions, contact your omron sales representative. approved standards consult your omron sales representative for specific models with standard approvals. ul1054 (file no. e41515)/csa c22.2 no. 55 (file no. lr21642) rated voltage v-21 v-16 v-15 v-11 v-10 125 vac 21 a, 1/2 hp 16 a, 1/2 hp 15 a, 1/2 hp 11 a, 1/3 hp 10 a, 1/3 hp 250 vac 125 vdc 0.6 a 0.6 a 0.6 a 0.6 a 0.6 a 250 vdc 0.3 a 0.3 a 0.3 a 0.3 a 0.3 a en61058-01 (file no. 129608, vde approval) rated voltage v-21 v-16 v-11 250 vac 20 (4) a 16 (4) a 11 (3) a testing conditions: 5e4 (50,000 operations), t105 (0 c to 105 c) en61058-1 (file no. t9451451, tv rheinland approval) rated voltage v-15 v-10 250 vac 15 a 10 a 250 vdc 0.3 a 0.3 a testing conditions: 5e4 (50,000 operations), t85 (0 c to 85 c)
v v 118 contact specifications item v-21 v-16 v-15 v-11 v-10 contact specification rivet material silver alloy silver gap (standard value) 1 mm (f gap) or 0.5 mm (g gap) inrush current nc 50 a max. 40 a max. 36 a max. 24 a max. no minimum applicable load 160 ma at 5 vdc contact form spdt spst-nc spst-no engineering data (reference values) mechanical durability (pin plunger models) v-21/-16/-15/-10 electrical durability (pin plunger models) v-21/-16/-15 number of operations (x10 ) 6 200 100 50 10 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 (1.6) 1.8 ambient temperature: 20 2 c ambient humidity: 65 5% without load operating frequency: 600 operations/min v-10 (0.98 n {100 gf}), v-11 v-10 (1.96 n {200 gf}) v-15 v-16 v-21 ot rated value operating frequency: 60 operations/min cos = 1, 250 vac 5 2 1 0.5 0.3 0.1 0 4 8 1216202428 v-21 v-15 v-16 5 2 1 0.5 0.3 0.1 0 0.5123456789101112 v-10 v-11 v-11/-10 full stroke ot (mm) switching current (a) switching current (a) ambient temperature: 20 2 c ambient humidity: 65 5% operating frequency: 60 operations/min cos = 1, 250 vac number of operations (x10 ) 6 number of operations (x10 ) 6
v v 119 dimensions terminals note: 1. all units are in millimeters unless otherwise indicated. 2. the following is for the spdt contact specifications. two terminals will be available for spst-no or spst-nc contact specific a- tions. for terminal positions, refer to contact form on page 118. 3. right-angle pcb terminal type is available d5 type: pins at right angles, to the right. d6 type: pins at right angles, to the left. drawings will be provided if requested. terminal type solder terminals (a) quick-connect terminals (#187) (c2) quick-connect terminals (#250) (c) screw terminals (b) com bottom position t = 0.5 three, solder terminals (10) 2.9 (6.5) (5.5) t = 0.5 three, quick-connect terminals (#187) (10) 2.9 (6.5) (5.5) t = 0.8 three, quick-connect terminals (#250) (12.0) 3.2 (7.7) (4.9) t = 0.8 three, #m3 0.5 3.2 phillips screw washer 3.1 (7) com side position (10) 2.4 (6.5) (5.5) (10) 2.4 (6.5) (5.5) (12.0) 3.6 (7.7) (4.9) --- terminal dimensions 1.6 dia. 2.4 dia. 4.75 0.1 6.35 3.2 (see note) note: indicates the length to the center of the 1.6-dia. holes 1.6-dia. terminal hole 4.75 0.1 3.2 6.35 1.65-dia. terminal hole 6.35 0.1 3.95 8.1 --- mounting holes two, 3.1-dia. mounting holes or m3 screw holes 10.3 0.1 22.2 0.1
v v 120 dimensions and operating characteristics note: 1. all units are in millimeters unless otherwise indicated. 2. unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. 3. the following illustrations and drawings are for quick-connect terminals (#250) (terminals c). v models with a switching curr ent of 16 a or 11 a incorporates terminals a and c2. these models are different from #250 models in terminal size only. terminals a, c 2, and side common terminals are omitted from the following drawings. refer to kinds of t erminals on page 1 19 for these terminals. 4. the in the model number is for the terminal code. 5. the operating characteristics are for operation in the a direction ( ). model v-21-1 6 v-16-1 5 of max. 3.92 n {400 gf} 1.96 n {200 gf} rf min. {g} 0.78 n {80 gf} {g} 0.49 n {50 gf} pt max. 1.2 mm ot min. 1.0 mm md max. 0.4 mm op 14.7 0.4 mm model v-11-1 4 v-11-1 5 of max. 0.98 n {100 gf} 1.96 n {200 gf} rf min. {g} 0.20 n {20 gf} {g} 0.49 n {50 gf} pt max. 1.2 mm ot min. 1.0 mm md max. 0.4 mm op 14.7 0.4 mm pin plunger models (without barrier) v-21-1 6 v-16-1 5 v-11-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t=0.8 three, quick-connect terminals (#250) 20.2 0.25 2.8 1.6 2.8 10.3 0.1 pt op 22.2 0.1 2.8 (12.0) 27.8 39.8 0.8 2.8 8.4 15.9 19.1 0.6 4.2 2.8 10.3 (with right-hand barrier) v-21-1 r6 v-16-1 r5 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t=0.8 three, quick-connect terminals (#250) 20.2 0.25 2.8 1.6 2.8 10.3 0.1 pt op 22.2 0.1 2.8 (12.0) 27.8 39.8 0.8 40.2 2.8 15.9 8.4 19.1 21.9 0.6 4.2 2.8 0.6 10.3 a a (with left-hand barrier) v-21-1 l6 v-16-1 l5 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t=0.8 three, quick-connect terminals (#250) 2.8 0.6 4.2 0.6 10.3 2.8 19.1 15.9 8.4 21.9 1.6 20.2 0.25 2.8 2.8 (12.0) 2.8 27.8 39.8 0.8 22.2 0.1 40.2 10.3 0.1 pt op a
v v 121 model v-211-1 6 v-161-1 5 of max. 3.92 n {400 gf} 1.96 n {200 gf} rf min. {g} 0.49 n {50 gf} {g} 0.49 n {50 gf} pt max. 1.6 mm ot min. 0.8 mm md max. 0.6 mm op 15.2 0.5 mm model v-111-1 4 of max. 0.98 n {100 gf} rf min. {g} 0.15 n {15 gf} pt max. 1.6 mm ot min. 0.8 mm md max. 0.6 mm op 15.2 0.5 mm model v-212-1 6 v-162-1 5 of max. 2.45 n {250 gf} 1.23 n {125 gf} rf min. {g} 0.25 n {25 gf} {g} 0.14 n {14 gf} pt max. 4.0 mm ot min. 1.6 mm md max. 1.5 mm op 15.2 1.2 mm model v-112-1 4 of max. 0.59 n {60 gf} rf min. {g} 0.06 n {6 gf} pt max. 4.0 mm ot min. 1.6 mm md max. 1.5 mm op 15.2 1.2 mm model v-213-1 6 v-163-1 5 of max. 1.27 n {130 gf} 0.69 n {70 gf} rf min. {g} 0.12 n {12 gf} {g} 0.06 n {6 gf} pt max. 9.0 mm ot min. 2.0 mm md max. 2.8 mm op 15.2 mm +2.6 ?3.2 model v-113-1 4 of max. 0.34 n {35 gf} rf min. {g} --- pt max. 9.0 mm ot min. 3.2 mm md max. 2.8 mm op 15.2 2.6 mm short hinge lever models v-211-1 6 v-161-1 5 v-111-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.8 three, quick-connect terminals (#250) 22.1 8.1 pt op 2.8 10.3 0.1 2.8 (12.0) 27.8 22.2 0.1 39.8 0.8 1.6 2.8 8.4 15.9 19.1 0.6 2.8 4.3 10.3 note: stainless-steel lever a 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.8 three, quick-connect terminals (#250) 35.6 0.8 8.1 1.6 pt op 2.8 10.3 0.1 22.2 0.1 (12.0) 2.8 27.8 39.8 0.8 2.8 15.9 8.4 19.1 0.6 2.8 4.3 10.3 hinge lever models v-212-1 6 v-162-1 5 v-112-1 4 note: stainless-steel lever a 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.8 three, quick-connect terminals (#250) 59.4 0.8 pt op 2.8 10.3 0.1 22.2 0.1 (12.0) 2.8 27.8 39.8 0.8 2.8 8.4 15.9 19.1 0.6 2.8 4.3 10.3 long hinge lever models v-213-1 6 v-163-1 5 v-113-1 4 note: stainless-steel lever 1.6 a
v v 122 model v-214-1 6 v-164-1 5 of max. 2.45 n {250 gf} 1.23 n {125 gf} rf min. {g} 0.25 n {25 gf} {g} 0.14 n {14 gf} pt max. 4.0 mm ot min. 1.6 mm md max. 1.5 mm op 18.7 1.2 mm model v-114-1 4 of max. 0.59 n {60 gf} rf min. {g} 0.06 n {6 gf} pt max. 4.0 mm ot min. 1.6 mm md max. 1.5 mm op 18.7 1.2 mm model v-215-1 6 v-165-1 5 of max. 4.71 n {480 gf} 2.35 n {240 gf} rf min. {g} 0.49 n {50 gf} {g} 0.49 n {50 gf} pt max. 1.6 mm ot min. 0.8 mm md max. 0.6 mm op 20.7 0.6 mm model v-115-1 4 of max. 1.18 n {120 gf} rf min. {g} 0.15 n {15 gf} pt max. 1.6 mm ot min. 0.8 mm md max. 0.6 mm op 20.7 0.6 mm model v-216-1 6 v-166-1 5 of max. 2.45 n {250 gf} 1.23 n {125 gf} rf min. {g} 0.25 n {25 gf} {g} 0.14 n {14 gf} pt max. 4.0 mm ot min. 1.6 mm md max. 1.5 mm op 20.7 1.2 mm model v-116-1 4 of max. 0.59 n {60 gf} rf min. {g} 0.06 n {6 gf} pt max. 4.0 mm ot min. 1.6 mm md max. 1.5 mm op 20.7 1.2 mm simulated roller lever models v-214-1 6 v-164-1 5 v-114-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.8 three, quick-connect terminals (#250) 3.5r 32.6 0.8 8.1 1.6 pt op 2.8 10.3 0.1 22.2 0.1 (12.0) 2.8 27.8 39.8 0.8 0.6 2.8 4.3 10.3 note: stainless-steel lever 2.8 15.9 19.1 8.4 a note: 1. stainless-steel lever 2. oilless polyacetar resin roller short hinge roller lever models v-215-1 6 v-165-1 5 v-115-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note 1) 4.8 dia. 4.8 (see note 2) t=0.8 three, quick-connect terminals (#250) 20.1 8.1 1.6 pt op 2.8 10.3 0.1 22.2 0.1 2.8 (12.0) 27.8 39.8 0.8 2.8 8.4 15.9 19.1 0.6 5.1 10.3 a hinge roller lever models v-216-1 6 v-166-1 5 v-116-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note 1) 4.8 dia. 4.8 (see note 2) t=0.8 three, quick-connect terminals (#250) 34.0 0.8 8.1 1.6 pt op 2.8 10.3 0.1 22.2 0.1 (12.0) 2.8 27.8 39.8 0.8 2.8 19.1 0.6 5.1 10.3 15.9 8.4 note: 1. stainless-steel lever 2. oilless polyacetar resin roller a
v v 123 thermosetting case (v-15/-10 models) the following illustration and drawing are for solder and quick-connect terminals (#187) (terminals a). v models with a switchi ng current of 15 a or 10 a incorporate terminals b or c2. these models are different from #187 models in terminal size only. refer to terminals on page 119 for these terminals. model v-15-1 5 v-10-1 5 v-10-1 4 of max. 1.96 n {200 gf} 0.98 n {100 gf} rf min. {g} 0.49 n {50 gf} {g} 0.20 n {20 gf} pt max. 1.2 mm ot min. 1.0 mm md max. 0.4 mm op 14.7 0.4 mm model v-151-1 5 v-101-1 5 v-101-1 4 of max. 1.96 n {200 gf} 0.98 n {100 gf} rf min. {g} 0.49 n {50 gf} {g} 0.15 n {15 gf} pt max. 1.6 mm ot min. 0.8 mm md max. 0.6 mm op 15.2 0.5 mm model v-152-1 5 v-102-1 5 v-102-1 4 of max. 1.23 n {125 gf} 0.59 n {60 gf} rf min. {g} 0.14 n {14 gf} {g} 0.06 n {6 gf} pt max. 4.0 mm ot min. 1.6 mm md max. 1.5 mm op 15.2 1.2 mm model v-153-1 5 v-103-1 5 v-101-1 4 of max. 0.69 n {70 gf} 0.34 n {35 gf} rf min. {g} 0.06 n {6 gf} {g} --- pt max. 9.0 mm 9.0 mm ot min. 2.0 mm 3.2 mm md max. 2.8 mm 2.8 mm op 15.2 mm +2.6 ?3.2 15.2 2.6 mm pin plunger models v-15-1 5 v-10-1 5 v-10-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t=0.5 three, solder terminals 20.2 0.25 2.8 2.8 10.3 0.1 pt op 22.2 0.1 2.8 27.8 (10) 37.8 0.8 15.9 18.8 4.2 2.8 10.3 a short hinge lever models v-151-1 5 v-101-1 5 v-101-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.5 three, solder terminals 22.1 8.1 pt 2.8 22.2 0.1 2.8 27.8 (10) 37.8 0.8 15.9 18.8 4.3 2.8 10.3 op 10.3 0.1 note: stainless-steel lever a hinge lever models v-152-1 5 v-102-1 5 v-102-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.5 three, solder terminals 35.6 0.8 8.1 pt op 2.8 10.3 0.1 22.2 0.1 2.8 27.8 (10) 37.8 0.8 15.9 18.8 4.3 2.8 10.3 note: stainless-steel lever a long hinge lever models v-153-1 5 v-103-1 5 v-103-1 4 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.5 three, solder terminals 22.2 0.1 27.8 2.8 (10) 15.9 18.8 10.3 0.1 op pt 8.1 4.3 2.8 10.3 37.8 0.8 59.4 0.8 2.8 note: stainless-steel lever a
v v 124 model v-154-1 5 v-104-1 5 v-104-1 4 of max. 1.23 n {125 gf} 0.59 n {60 gf} rf min. {g} 0.14 n {14 gf} {g} 0.06 n {6 gf} pt max. 4.0 mm ot min. 1.6 mm md max. 1.5 mm op 18.7 1.2 mm model v-155-1 5 v-105-1 5 v-105-1 4 of max. 2.35 n {240 gf} 1.18 n {120 gf} rf min. {g} 0.49 n {50 gf} {g} 0.15 n {15 gf} pt max. 1.6 mm ot min. 0.8 mm md max. 0.6 mm op 20.7 0.6 mm model v-156-1 5 v-106-1 5 v-106-1 4 of max. 1.23 n {125 gf} 0.59 n {60 gf} rf min. {g} 0.14 n {14 gf} {g} 0.06 n {6 gf} pt max. 4.0 mm ot min. 1.6 mm md max. 1.5 mm op 20.7 1.2 mm simulated roller lever models v-154-1 5 v-104-1 5 v-104-1 4 3.5r 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note) t=0.5 three, solder terminals 22.2 0.1 27.8 2.8 (10) 15.9 18.8 10.3 0.1 op pt 8.1 4.3 2.8 10.3 37.8 0.8 32.6 0.8 2.8 note: stainless-steel lever a 4.8 dia. 4.8 (see note 2) 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note 1) 22.2 0.1 27.8 2.8 (10) 15.9 18.8 10.3 0.1 op pt 8.1 5.1 10.3 37.8 0.8 20.1 2.8 short hinge roller lever models v-155-1 5 v-105-1 5 v-105-1 4 note: 1. stainless-steel lever 2. oilless polyacetar resin roller a t=0.5 three, solder terminals hinge roller lever models v-156-1 5 v-106-1 5 v-106-1 4 4.8 dia. 4.8 (see note 2) 3.1 +0.13 ?0.03 dia. holes 3.1 +0.13 ?0.03 3.4 0.15 dia. t = 0.5 (see note 1) 22.2 0.1 27.8 2.8 (10) 15.9 18.8 10.3 0.1 op pt 8.1 5.1 10.3 37.8 0.8 34.0 0.8 2.8 note: 1. stainless-steel lever 2. oilless polyacetar resin roller a t=0.5 three, solder terminals
v v 125 precautions refer to pages 26 to 31 for common precautions. correct use specifications approved by tv rheinland according to en61058-1 appropriate cable size (mm 2 ) model solder terminals screw terminals v-10 0.75, 1.25, 2.0 0.75, 1.25 v-15 1.25, 2.0 1.25 use m3 crimp terminals for connecting to the screw terminals. applicable m3 crimp terminals: daido solderless terminal mfg. co., ltd. f1.25?3 j.s.t. mfg. co., ltd. 1.25 b3a mounting use m3 mounting screws with plane washers or spring washers to securely mount the switch. tighten the screws to a torque of 0.39 to 0.59 n m {4 to 6 kgf cm}. insulation distance according to en61058-1, the minimum insulation thickness for this switch should be 1.1 mm and minimum clearance distance be- tween the terminal and mounting plate should be 1.9 mm. if the in- sulation distance cannot be provided in the product incorporating the switch, either use a switch with insulation barrier or use a sepa- rator to ensure suf ficient insulation distance. refer to separator on page 152. actuator (sold separately) various actuators are available as shown on pages 152 to 155. connector (sold separately) refer to terminal connectors on page 282. all dimensions shown are in millimeters. to convert millimeters into inches, multiply by 0.03937. to convert grams into ounces, multiply by 0.03527. cat. no. b010-e1-09b

▲Up To Search▲

Price & Availability of V-15-1A5

	To Download V-15-1A5 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .